[Linux] HP hpasmcli command 로 시스템 상태 확인

#hpasmcli

HP management CLI for Linux (v1.0)

Copyright 2004 Hewlett-Packard Development Group, L.P.

--------------------------------------------------------------------------

NOTE: Some hpasmcli commands may not be supported on all Proliant servers.

      Type 'help' to get a list of all top level commands.

--------------------------------------------------------------------------

hpasmcli> help

CLEAR  DISABLE  ENABLE  EXIT  HELP  QUIT  SET SHOW

hpasmcli> show asr

ASR timeout is 10 minutes.

ASR is currently enabled.

hpasmcli> show boot

First boot device is: CD-ROM.

One time boot device is: Not set.

hpasmcli> show dimm

DIMM Configuration

------------------

Cartridge #:   0

Module #:      3

Present:       Yes

Form Factor:   9h

Memory Type:   12h

Size:          512 MB

Speed:         400 MHz

Status:        Ok

Cartridge #:   0

Module #:      4

Present:       Yes

Form Factor:   9h

Memory Type:   12h

Size:          512 MB

Speed:         400 MHz

Status:        Ok

hpasmcli> show f1

The POST F1 prompt is currently delayed.

hpasmcli> show fans

Fan  Location        Present Speed  of max  Redundant  Partner  Hot-pluggable

---  --------        ------- -----  ------  ---------  -------  -------------

#1   PROCESSOR_ZONE  Yes     NORMAL 18%     Yes        2        Yes           

#2   PROCESSOR_ZONE  Yes     NORMAL 18%     Yes        1        Yes           

#3   I/O_ZONE        Yes     NORMAL 18%     Yes        1        Yes           

#4   I/O_ZONE        Yes     NORMAL 18%     Yes        1        Yes           

#5   PROCESSOR_ZONE  Yes     NORMAL 18%     Yes        1        Yes           

#6   PROCESSOR_ZONE  Yes     NORMAL 18%     Yes        1        Yes           

#7   POWERSUPPLY_BAY Yes     NORMAL 18%     Yes        1        Yes           

#8   POWERSUPPLY_BAY Yes     NORMAL 18%     Yes        1        Yes           

hpasmcli> show ht

Processor hyper-threading is currently disabled.

hpasmcli> show iml

The IML Log is empty.

hpasmcli> show ipl

IPL (Standard Boot Order)

-------------------------

#0 CDROM

#1 Floppy

#2 USBKEY

#3 HDD

#4 PXE

hpasmcli> show name

No Server name seems to have been set, or command failed.

Please use "SET NAME" to set a server name.

hpasmcli> show powersupply

Power supply #1

Present  : Yes

Redundant: No

Condition: Ok

Hotplug  : Supported

Power supply #2

Power Supply not present

hpasmcli> show pxe

PXE boot status (2 Embedded NICs):

NIC1: PXE enabled

NIC2: PXE disabled

hpasmcli> show serial bios

BIOS console redirection port is currently set to COM1/9600.

hpasmcli> show serial bios

Embedded serial port A: COM1

Embedded serial port B: Disabled

hpasmcli> show serial virtual

The virtual serial port is currently COM2.

hpasmcli> show server

System        : ProLiant DL385 G1

Serial No.    : SGH532X0KK      

ROM version   : A05 06/14/2005

iLo present   : Yes

Embedded NICs : 2

NIC1 MAC: 00:14:38:4c:62:3e

NIC2 MAC: 00:14:38:4c:62:3d

Processor: 0

Name         : AMD Opteron

Stepping     : 2

Speed        : 2200 MHz

Bus          : 0 MHz

Socket       : 2

Level2 Cache : 1024 KBytes

Status       : Ok

Processor: 1

Name         : AMD Opteron

Stepping     : 2

Speed        : 2200 MHz

Bus          : 0 MHz

Socket       : 1

Level2 Cache : 1024 KBytes

Status       : Ok

Processor total  : 2

Memory installed : 1024 MBytes

ECC supported    : Yes

hpasmcli> show temp

Sensor   Location              Temp       Threshold

------   --------              ----       ---------

#0        SYSTEM_BD             -          -       

#1        CPU#1                51C/123F   80C/176F 

#2        I/O_ZONE             52C/125F   62C/143F 

#3        CPU#2                46C/114F   80C/176F 

#4        PROCESSOR_ZONE       41C/105F   60C/140F 

#5        POWER_SUPPLY_BAY     41C/105F   51C/123F 

hpasmcli> show uid

UID is currently off.

hpasmcli> show wol

Wake-On-Lan is currently enabled.

hpasmcli> show boot

First boot device is: CD-ROM.

One time boot device is: Not set.

hpasmcli> exit